12 Facts About Fiat Panda Key Fob Replacement That Will Refresh Your Eyes At The Water Cooler

Reasons Your Fiat 500 Key Fob Won't Work

A key fob from Fiat 500 allows you to easily open doors and start your car. There are a variety of reasons why the fob could stop working. It could be due to a dead battery or damage to the receiver module, water issues, or interference.

This listing is for a new fiat 500 key replacement fiat replacement car keys Flip Key Remote - like the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). It comes with trunk, lock and unlock buttons.

Dead Coin Battery

A dead battery is the most common cause of your 500 key fob being inoperative. Modern key fobs have a limited operating range and must be within a few feet of the vehicle to function. If you're far from your vehicle, and you press the key fob button the car won't respond and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery on your coin cell (Part number CR2032) by a new one from a reputable manufacturer like Panasonic, Duracell, or Energizer. You can find them at your local hardware store or online.

After you've replaced the battery in the coin cell You can test it by standing next to your Fiat 500 and pressing the buttons. The parking lights should blink and the key fob should operate the lock and unlock switches.

If your key fob isn't working even after replacing the battery, it may be water damage that prevents it from interacting with the module inside your vehicle. Water damage can happen in a number of ways, from the slightest splash to submerging your fob in salt water at the beach. If you suspect that your fob was exposed to water, try placing it in a dry rice bag to pull the moisture out. If that doesn't work, your fob will probably need to be reprogrammed by an experienced auto locksmith or the dealer.

Water Damage

Water damage can happen if you submerge the fob in the ocean or wash it in a washing machine. Saltwater can cause the circuit board to short and then cease to function. In the event that you let your fob get wet, it's not an option, but if you drop it into the water in a cup or do not remember to take it out of your pocket before you run the washer do not give up hope.

Remove the battery first. Clean the electronic chip with isopropyl alcohol or a similar product and dry it completely before replacing the battery. Next test the fob to verify if it is working. If the key still doesn't work, it may have to be reset. This is usually handled by an auto locksmith or dealer.

If the key is older and has not been programmed to your car It is likely that it needs to be replaced completely. A professional locksmith for automotive will be able to complete this process. The locksmith will need the key cut to match the car's ignition. The locksmith also needs to reprogram the fob into the car's system. This is a low-cost and quick process that could be completed on the same day.

Receiver Module Issues

The 500 key fob could not work because it's out of range. The remote usually has an area of 30 feet or less and if it's far away from your car it will not respond to your commands. This can be easily fixed by moving it closer to your vehicle until it starts responding.

If you've replaced the battery on your coin (commonly known as a "button" or "watch") and the fob won't work it could be due to an internal circuit board problem. Reprogramming the fob typically resolves this issue. You can find directions on how to do this for the majority of automobiles by searching YouTube or checking out the owner's manual.

It is possible to replace the metal clips that hold the coin batteries in their place. If they loose tension, it can prevent the battery from being seated properly, and this will result in the malfunction of your remote.

In rare cases it is possible that the fob will become desync'd with your vehicle due to software problems or hardware issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases, the software may also require reinstallation in your body control modules.

Interference

Interference can also cause the key fob not to receive or transmit signals. This could occur if the key fob is close to a radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob might not function include a poor connection to the buttons or damage to the internal chip, or water damage.

If the key fob been unable to function for a while in the middle of the night or even after trying everything you can do at home to solve it e.g. It could be a defective 500 receiver module in the event that you've tried replacing the battery, reprogramming or using a spare key fob. The receiver module, which is located beneath the dashboard, picks up radio frequency signals from your key fob. It converts the signals into electronic commands that are then read by the vehicle.

Luckily, there is an easy way to reset all of the onboard systems in your 500 and include the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and allow you to restart the computer in your car. This will help you get your key fob to function again. If the problem persists you should speak with an expert technician. They will be able diagnose the root cause of any issues.