15 Of The Best Pinterest Boards All Time About Fiat Panda Key Fob Replacement

Reasons Your Fiat 500 Key Fob Won't Work

A key fob for the fiat car key cutting 500 is a handy way to unlock the doors and start the car. There are a myriad of reasons why the key fob might stop working. This includes a dead battery or water damage, issues with the receiver module, and interference.

This listing is for an NEW replacement fiat key fiat 500 remote key Flip Key Remote that appears similar to the Ilco brand. It needs to be professionally programmed (click here to search for local automotive locksmiths). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the main cause of your 500 key fob not working. Modern key fobs have a very limited range of operation, and must be within only a few feet from the vehicle to function. If you are far from your vehicle and press the key fob button, the car won't be able to respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the battery on your coin cell (Part number CR2032) by a new key for fiat 500 one from a reputable brand like Panasonic, Duracell, or Energizer. You can find them at your local hardware store or on the internet.

You can test the coin-cell battery by pressing the buttons while you are standing close to your fiat scudo key replacement 500. The parking lights should blink and the key fob should operate the lock and unlock switch.

If your fob's key doesn't work even after replacing the battery, it could be water damage that has prevented it from connecting to the module in your vehicle. Water damage can happen in a variety of ways, from a light splash to submerging the fob into salt water at the beach. If you think your fob was exposed to water, put it in a bag of rice to draw out the moisture. If that doesn't work your fob is likely to need to be reset by an experienced auto locksmith or the dealer.

Water Damage

While the fob comes with rubber seals to keep water from the electronic chip inside it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short, and eventually cease to function. The fob getting wet is not an ideal choice but if you accidentally drop it in a cup of water or don't remember to remove it from your pants pocket before running the washer do not give up hope.

First remove the battery from the fob. Clean the electronic chip with isopropyl alcohol or a similar product and then dry it thoroughly before replacing the battery. Check the fob to determine if it's working. If the key does not function, it may have to be changed. This is usually done by an auto locksmith or dealer.

If the key is a newer model and was not programmed to your car It will most likely need to be replaced completely. This is a simple process that can be completed by a professional locksmith for automotive use. The locksmith will need the key to be cut to match the car's ignition. The locksmith also needs to reprogram the fob into the car's system. This is a fast and cost-effective process that is usually completed the next day.

Receiver Module Issues

One of the simplest reasons your 500 key fob may stop working is because it's out of range. The remote's range is of 30 feet, so when you're too far away from your vehicle it won't be able to respond to your commands. This can easily be resolved by moving it closer to your vehicle until it begins responding.

If you've replaced the battery in your coin (commonly known as"button" or "button" or "watch") and the fob won't work, it could have an internal circuit board issue. In the majority of cases, reprogramming your fob will fix the issue. You can find instructions on how to do this for most vehicles by searching YouTube or consulting the owner's manual.

It is sometimes necessary to replace the metal clips that hold the coin batteries in the correct position. If they loose tension, it could hinder the battery from sitting properly and could cause the remote to malfunction.

In rare instances it is possible that the fob will become disconnected from your vehicle due to software problems or hardware issues. This could be a huge headache, but you can frequently fix this issue by visiting a local dealer or auto locksmith to reprogram your fob for you. In some cases the software may require reinstallation to your body control modules.

Interference

In addition to a dead coin battery the key fob could not be receiving or transmitting the signal due to interference. This is possible when the key fob is in proximity to the radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob may not function may be a lack of connection to the buttons or the internal chip, or water damage.

If the key fob been unable to function for a while in the middle of the night, or after trying everything you can at home to fix it e.g. replacing the battery, reprogramming, and using the spare key fob, it could have a faulty receiver module on your 500. The receiver module, which is located beneath the dashboard, picks up radio frequency signals from your key fob. It converts the signals into electronic commands, which are then read by the vehicle.

Fortunately, there's an easy method of resetting all on-board systems in your 500, including the key fob. Disconnect the battery 12 volt for about 15 minutes, by removing the negative cable first then the positive cable. Reconnect the battery. This will remove any remaining electric current, and also restart the computer of your car. This can help get your key fob to function again. If the issue persists, you should consult an expert certified technician. They can identify the exact cause of any issues.