The No. One Question That Everyone Working In Patio Door Lock Repair Must Know How To Answer

Patio Door Lock Repairs

Over time, patio door lock repairs near me door wear and tear can cause lock malfunctions. There are fortunately, a number of simple and efficient methods that can restore your uPVC patio door's security.

These easy fixes will make your home safer no matter if you adjust the lock or clean the locking mechanism.

Clean the Lock

Although patio screen door repair near me doors are a great way to bring the outside in and keep the elements out, they can also be an issue for security in the event that your lock isn't operating as it should. Over time, wear and tear, cold and hot weather, dirt, and debris can cause your patio door lock to become difficult to operate. With a little care, you can ensure the locks on your patio door always perform effectively.

It is important to first clean the patio door lock and all moving parts. This will help get rid of any grime and coatings that may be preventing the lock from functioning as it should. Start by wiping the moving parts on your patio door lock using a damp cloth. Then you can use a scouring paper or rough damp cloth to scrub the dirt-infested areas of the door frame and frame. You should then wipe down the entire lock using a dry cloth to remove any remaining dampness and allow it to dry completely before making use of it again.

If you have an exterior door that is fitted with pin tumbler latch mechanisms it is possible to lubricate the lock by applying powdered graphite to the key or applying an lubricant based on Teflon such as WD-40 Multi-Use Product. This kind of lubricant can be applied quickly and doesn't dissolve over time. If you're unable to locate a suitable lubricant you could try using a pencil with an extremely sharp tip. Place the pencil in the lock and move it around to distribute the graphite.

Sliding patio door tracks also require regular maintenance to ensure they're free of dust, dirt, and debris. These tracks can be especially vulnerable to snow and ice, which could cause them to become stuck or slack, making it harder for your patio doors to open and close.

Clean the track rails and rollers on sliding patio doors by removing damaged or dirty weather stripping. Clean it and replace it. Patio door rollers can also be cleaned and sprayed down with a nonstick lubricant.

Lubricate the Moving Parts

uPVC French doors, like sliding patios, are operated with 3 to 4 or sometimes 5 point locking mechanisms. These include the lock cylinder and handle that is operated with the key. These doors also need maintenance, and specifically lubrication of the moving parts. This can be done using a thin oil (never WD40) and is recommended to be done at least once per year.

If sagging hinges aren't the cause, the door may be misaligned and catching or rubbing against the strike plate hole within the frame. Remove the strike plate, and employ a sharp tool to expand the mortise. This will allow the latch to fit properly into the hole, and also prevent it from hitting the frame.

Once the cylinder is cleared of the way take a measurement of its width using the help of a book or piece wood that can fit into the adjustment screw gap above the lock. The outer dimension is measured from the outside of the door to the center of cylinder. The inner dimension is measured from the center adjustment screw to the end cylinder.

Check the Lock's Width

If your patio door latch is difficult to turn, even after cleaning and lubricating, there's a possibility that it is out of alignment with the strike plate hole. Check if your door is balanced, and if the hinge screws are in good condition. In most cases, however, simply moving the strike plate downwards or upwards could fix the problem.

Most of the time, the issue occurs when the strike of the lock is too small for the latch to engage. In this situation, you need to widen the opening using the hammer and chisel. Then, test the latch to ensure it does not rub against the jamb frame of the door or fall on it.

It is important to identify the type of mortise lock you have before purchasing an alternative. This can be done by looking at the faceplate and determining if it is round or square. Examine each screw hole on the current lock, and note their size. This information will allow you to find a replacement lock that is exactly the same width and will fit in the hole you have already.

You'll need to locate the mortise lock and inspect it for bends, scratches or other damage that need to be repaired. A bent or damaged latch is more prone to break than one that's been frequently used, so be sure to replace the lock with a brand new, secure version when you spot any indications of damage or wear.

After you've examined the lock and identified which type of replacement you'll need now is the time to start working on the actual repair patio door lock. The spindle and handle must be removed from the doorway to the patio. Insert the new handle. Start by putting in the interior handle by aligning it with the spindle, and then securing it by using the two screws or bolts that secure it. Install the exterior handle following the interior handle. After you've completed these steps check the handles to ensure that they open and shut easily and that the latch is in contact correctly with the strikeplate.

Check the Door's Strike

The strike plate and the door latch are two pieces that work together in order to secure the door. If these are misaligned and the latch isn't latching the door shut correctly. Fortunately, the issue is usually simple to fix.

Check the holes for receiving of the strike plate to make sure they are clear of obstructions, such as dirt or plastic plugs. Then, loosen the keeper screws that secure the strike plate in place, allowing it to move horizontally, but not separating it from the frame of the door. Adjust the strike plate so that it aligns its holes for receiving with the latch hooks of the door latch. After the strike plate has been adjusted then tighten all screws, and test to see if the door closes smoothly.

These plates are difficult to reach for homeowners with sliding patio doors. However they are vital to secure and unlock your door. The plates made of metal are located on the top and bottom jambs of the door, which are where they help support the latch. The door latch is inserted into this strike plate and creates an airtight seal. If the strike plate is damaged, rusted, or not properly installed, it could hinder the latch from locking the door securely.

A misalignment of the strike plate and latch is one common cause for a patio lock to not close or stay. The most effective way to test for this is to perform the "lipstick test." Rub some lipstick on the edge of the deadbolt, then put masking tape on it. The lipstick will leave a mark when you shut the door. This will show you exactly where the latch meets the strike plate. If the mark is too low or high, you can easily alter the strike plate.

If your patio door locks for sliding aren't working correctly they could be a problem in keeping your home safe from burglars. You need to resolve this issue as quickly as you can. Follow these steps to repair patio doors your patio door lock and restore it's functionality.