10 Facts About Kia Picanto Key Replacement That Can Instantly Put You In A Good Mood

How to Fix a Dead Kia Picanto Key Fob

The Kia Picanto was built for the city. It swerves through traffic snaking areas that bigger cars can't and breezes through width restrictions as if they're not even there. Although it has a shabby look, it packs in plenty of tech.

There are a myriad of reasons for why your kia picanto key fob may not be functioning. A dead battery is the most common cause.

Dead Coin Battery

The most common reason why a Kia Picanto key fob stops working is a dead or dying battery. Usually, the key fob will show warning signs prior to dying in a way, like losing the range or showing irregular behavior. It is best to replace your battery in the event that you observe any of these warning signs prior to the battery fails completely. Choose a replacement car key kia battery that has the same voltage, size, and specifications as the original.

If the fob for your key is not working, you might be required to take it to a dealer. This is the only way to guarantee the replacement is programmed correctly and compatible with your vehicle. The process of reprogramming keys without following the proper procedure can damage the chip inside and cause it to stop working.

Another possibility is that the receiver module has developed an issue. This could be due to a damaged chip or simply wear and tear over time. It can be difficult to identify the signs of this issue, but it is important to look into the issue immediately. If your key fob isn't working, or if the spare doesn't function, you should contact a dealership for help. They'll be able identify the issue and fix it for you.

Faulty Chip

The key fob contains the chip that sends the signal to a computer in the car. If the chip is damaged it will not send the correct code and the immobilizer system of the car will be activated. This can be caused by various reasons. One reason is a low battery on the key fob. Another issue is water damage. If the fob becomes wet, it is very likely that it will cease to function.

A malfunctioning chip could be the reason why a Picanto fob isn't turning on the engine. If you've replaced the battery, reprogrammed it and then inserted the fob and it still doesn’t work the circuit board could be damaged. If this is the case, you'll need to replace it.

To open the Fob, you will need to press on the button on the back of the fob. Once you have done this, you are able to take off the mechanical key. Then, follow the video below to replace the key fob's battery. Be sure to use the correct battery with the same size and voltage. Using the wrong type of battery can cause damage to the Fob. Press the lock button after replacing the battery. If it works, then you have a reliable Fob.

Faulty Receiver Module

Your key fob isn't impervious to damage and can take a lot of abuse. Over time, its battery contacts and buttons can become damaged and stop working properly. It's simple to repair it with a couple of tools.

The fob has to transmit a message to a receiver inside your car in order for it to work. If this module is defective the fob won't be able of opening or starting your car. There are a myriad of possible causes for this issue however the first thing to try is resetting the fob.

This is accomplished by disconnecting the cable and leaving the battery at 12 volts drain completely. Then, connect the negative and positive cables in reverse order.

If the battery is in good health and the fob doesn't have any water damage, the problem could be related to the signal. This could be due to many factors, including interference from nearby transmitters and objects that use the exact same frequency band as the Receiver of Picanto.

Key fobs are constructed with rubber seals that prevent the chip from getting wet, but if they're submerged for a long period of time, the chips can be destroyed. This is why it's crucial to always keep your key fob free from water, and to only use a key fob with water-proof design.

Poor programming

A Kia Picanto key fob is a convenient way to unlock and start your vehicle. It can also be used to control your vehicle's features. It is essential to know how to use your key fob, especially when you're traveling in harsh conditions or have a limited mobility. There are plenty of kia key fob replacement Picanto key fob tips to help you with this!

If your key fob stops working out of the blue it could be an issue with its internal chip. It is rare however it is possible. To determine the problem, it is best to consult a kia ignition key replacement dealer.

You can also try to reset your Picanto key fob. The procedure is fairly simple and can be completed at home. The first step is to remove the key fob from the ignition switch. Then connect the diagnostic tool to the OBDII port under the dash and then turn on the engine. The diagnostic tool will ask you for information regarding the Picanto. This includes the VIN, the make, and model.

You can also examine the battery for dead coin battery. The metal clips on the key fob are used to hold the battery and complete the circuit. If the retaining clips are loose, they can disrupt the flow of electricity and result in a loss function.