10 Things That Your Family Taught You About Fiat Panda Key Fob Replacement

Reasons Your fiat 500 replacement key fob 500 Key Fob Won't Work

A fiat 500 key fob is a great way to unlock the doors and get started the car. However, there are numerous reasons the fob could stop working. This includes a dead battery or water damage, problems with receiver modules, as well as interference.

This listing is for an NEW replacement fiat ducato key fob replacement Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to find local locksmiths for your vehicle). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why your 500 key fob doesn't work is a dead battery. Modern key fobs have a very limited operating range and should be within only a few feet from the vehicle to function. If you are far from your car and press the keyfob button, it will not respond and display the message "Key Fob Not Detected".

If this happens, replace the battery of your coin cell (Part number CR2032) with a new one from a reputable manufacturer such as Panasonic, Duracell, or Energizer. They are usually available at your local hardware store, or online.

After you've replaced the battery in the coin cell you can test it by standing next to your fiat 500x key fob 500 and pressing the buttons. The parking lights should blink and the key fob will operate the lock and unlock switch.

If your fob's key doesn't work even after replacing the battery, there may be water damage that hinders it from interacting with the module in your vehicle. Water damage can happen in many ways, including simply splashing or submerging the key fob into saltwater at the beach. If you believe your fob was exposed to water, put it in a bag of rice to draw out the moisture. If this doesn't work your fob is likely to need to be reprogrammed by a professional auto locksmith or by the dealer.

Water Damage

Water damage can occur if you submerge the fob in the ocean, or wash it in a machine. Saltwater poses a particular risk to the circuit board of the fob, causing it to short out and eventually end up dying. If you get the fob wet, it's not a good idea but if you drop it into the water in a cup or don't remember to remove it from your pants pocket before running the washing machine Don't give up hope.

Remove the battery first. Before replacing the battery, clean the electronic chip using isopropyl or similar products. Check the fob again to check if it's functioning. If the key doesn't work, it might need to be programmed again. This is usually done by an auto locksmith or dealer.

If the key is newer and hasn't been programmed to your vehicle It will most likely need to be replaced completely. A professional locksmith for cars can complete this simple process. The locksmith will have to cut the key to match the ignition of your car. The locksmith also needs to reprogram your fob in the car's system. This is an affordable and quick procedure that can be completed in the same day.

Receiver Module Issues

Your 500 key fob might not function because it's out of range. The remote's range is of 30 feet. Therefore, in the event that you are far from your car it will not respond to your commands. You can solve this problem by moving the remote closer to your vehicle until it responds.

If your fob doesn't work after you replace the battery in the coin, also called a "button", "watch" or "button" it could be a problem with the internal circuit board. In the majority of cases, reprogramming your fob will resolve this issue. You can find the steps for most vehicles on YouTube or in the owner's manual.

You may need to replace the metal retaining clips that hold the coin battery. If they lose tension it can prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare instances, the fob can become out of connection with your vehicle as a result of hardware or software issues. This could cause a significant issue, but you are able to frequently fix this issue by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In some cases the software might require reinstallation into your body control modules.

Interference

In addition to a dead battery on a coin, the key fob may not be able to receive or transmit a signal due to interference. This could happen if the key fob is in proximity to a radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. The key fob may not function because of a weak connection with the buttons or water damage, or damage to the internal chips.

If the key fob has stopped working one day out of the blue or even after trying everything you can at home to resolve it e.g. replacing the battery, reprogramming it and using the spare key fob, you could have a defective receiver module on your 500. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. It then converts them into electronic commands that the vehicle interprets.

There's a quick and easy way to reset the 500's on-board system including the keyfob. Disconnect the 12 volt battery for about 15 minutes by removing the negative cable first then the positive cable. Then, reconnect the battery. This will remove any remaining electrical charge, and then restart the computer in your car. This could help you get your key fob to work again. If the issue continues, you should consult an expert technician. They will be able to identify the exact cause of any problems.