Will Patio Door Lock Repair Always Rule The World?

Patio Door Lock Repairs

Over time, patio doors undergo wear and tear that could cause lock malfunctions. There are a few simple steps you can take to restore the security of your uPVC door.

It's about realigning the lock or cleaning the mechanism for locking These simple fixes can increase the security of your home.

Clean the Lock

Patio doors are ideal to let the outdoors in and keeping out the elements. However they can pose risky for security if the lock doesn't work properly. Over time, wear, tear, cold and hot weather dirt and debris can cause your patio door lock to become difficult to operate. With some minor maintenance you can ensure that your patio door's locks will always perform properly.

It's important to first clean the patio door lock as well as all moving parts. This will help remove any dirt or coatings that may be preventing the lock from working properly. Begin by wiping down all the moving parts of your patio door's lock with a damp cloth, then employ a scouring pad or rough damp cloth to scrub any hard-to-reach parts of the door and frame that are covered in dirt. Then clean the lock with a dry towel to remove any remaining moisture. Let it air dry before using it.

If you have a patio door frame repair door that uses a pin tumbler latch mechanism, you can grease the lock by applying powdered graphite to the key or applying a lubricant made of Teflon, like WD-40 Multi-Use. This type of lubricant can be easy to apply and it won't disintegrate as time passes. If you're unable to find a suitable lubricant, you can try using a pencil that has an extremely sharp tip. Place the pencil in the lock and move it around to spread the graphite.

Sliding patio door tracks also require regular maintenance to ensure they're free of dust, dirt, and debris. They are particularly susceptible to ice and snow which could cause them to jam or bind, making it harder for your emergency patio door repair doors to open and close.

Sliding patio door track rails and rollers can be cleaned by removing any dirty or damaged weather stripping and then cleaning it, before replacing it. The same is true to glass patio door repair door rollers which can be cleaned and sprayed with a non-stick lubricant to help them move freely.

Lubricate the moving parts

uPVC french doors, like sliding patio doors, work with 3 to 4 or sometimes 5-point locking mechanisms which include the handle and lock cylinder operated by a key. These doors require maintenance, oiling of the moving parts. This can be done using a thin oil (never WD40) and is recommended to be done at least once per year.

If hinges that are sagging don't cause the issue, it could be that the door isn't aligned. It may be rubbing or catching against the hole of the strike plate in the frame. The solution is to take off the strike plate and use an abrasive chisel, which will enlarge the mortise it sits in. This allows the latch to fit perfectly in the hole and prevents scratching or catching on the frame.

Once the cylinder is cleared of the way take a measurement of its width using the help of a book or piece wood that can fit into the gap of adjustment screw above the lock. The outer dimension is measured from the outside of the door to the center cylinder. The inner dimension is measured from the center adjustment screw to the end of the cylinder.

Check the lock's width

If your patio door latch is hard to turn, even after cleaning and oiling it's possible that it's not aligned properly with the strike plate. Verify that the door is properly balanced and if the hinge screws are in good condition. In a lot of cases, moving the strike plate upwards or downwards will solve the issue.

Most of the time, the issue occurs when the lock's strike is too small for the latch to properly engage. In this instance, you can widen the opening with an hammer and chisel. Then, test the latch to ensure that it doesn't rub against the door jamb frame or catch on it.

You must identify the kind of mortise lock you have before purchasing an alternative. This can be done by looking at the faceplate and determining if it is round or square. Then, take a look at the screw holes on the current lock and note the dimensions of each. This will help you to find an alternative lock that is exactly the same size and fits into the hole you have already.

You'll need to locate the mortise lock and examine it for bends, scratches or other damage that requires to be repaired. A badly bent or damaged latch is more likely than one that has been used a lot to break. Replace the lock if it shows evidence of damage.

Once you've decided on the kind of lock replacement that you require It's time to begin the actual repair. The old spindle and handle should be removed from the patio door. Install the new handle. Begin by installing the handle in the interior by aligning it with the spindle, and then fixing it by using the two bolts or screws which hold it. Install the exterior handle following the interior handle. Once you have completed these steps, test the handles to ensure that they can be shut and open easily and that the latch is in contact correctly with the strikeplate.

Check the Strike on the door.

The door latch and strike plate are the two parts of the lock that work to ensure that the latch is secure the door. Misaligned strike plate and door latches can cause the latch to not latch the door correctly. Fortunately, the issue is often easy to fix.

First, check the strike plate's receiving holes to ensure they are clear of obstructions, such as dirt or plastic plugs. Then loosen the screws that hold the strike plate in place, allowing it to move vertically but not removing it from the door frame. Then, adjust the strike plate to ensure that its receiving holes align with the latch hooks on the door latch. After the strike plate has been adjusted then tighten the screws and then test the door to determine whether it locks smoothly after the new adjustment.

These plates are difficult to reach for homeowners who have sliding patio doors. However they are vital for locking and unlocking your door. These plates are usually placed on the top and bottom of the door jamb, which is where they are used to support the door's latch. The door latch is able to slide into the strike plate to form the seal when it is closed. If the strike plate has been damaged or rusted, or if it is not properly installed the latch might not be able to lock the door properly.

A misalignment of the strike plate and latch is the most common reason for the patio lock not to close or remain in place. The easiest way to check for this is to perform the "lipstick test." Apply some lipstick on the edge of the deadbolt, then put masking tape on it. When you shut the door the lipstick will leave an impression on the tape that will show exactly where the latch connects to the strike plate. If the mark is too high or low you can easily adjust the strike plate.

Locks for sliding patio doors help keep your home safe from burglars. If they're not functioning properly, you need to fix the problem quickly. Follow these easy steps to fix your patio door lock and restore its functionality.